Snake Grips &
Band-It® Tools |
 Lewis Snake Grips LSG
 The Lewis Snake Grip expands or contracts to grip different or identical cable and/or rope sizes as per the customer's needs. Save time stringing up, changing and unstringing because the snake requires no special tools. the swivel and swing link go smoothly through blocks and prevent line twisting. Install new cable by using old existing cable as pulling line. Always seize the ends of the grips by banding or taping.
|
| Regular Size LSG Snakes |
| Part No. / Size Range |
Approx.
Brk. Stgth. |
Work Load |
| LSG 1/4" - 1/2" |
4,400 lbs. |
1,200 lbs. |
| LSG 1/2" - 1" |
7,500 lbs. |
2,500 lbs. |
| LSG 1" - 1 1/2" |
10,000 lbs. |
3,500 lbs. |
| LSG 1 1/2" - 2" |
12,000 lbs. |
4,000 lbs. |
| LSG 2" - 2 3/4" |
16,000 lbs. |
5,000 lbs. |
| LSG 2 3/4" - 3 1/2" |
20,000 lbs. |
6,500 lbs. |
| LSG 3 1/2" - 4 1/4" |
24,000 lbs. |
8,000 lbs. |
|
| Special Size LSG Snakes |
| Part No. / Size Range |
Approx.
Brk. Stgth. |
Work Load |
| LSG 1/4" - 1 1/2" |
4,400 lbs. |
1,200 lbs. |
| LSG 1/2" - 1 1/2" |
7,500 lbs. |
2,500 lbs. |
| LSG 1/2" - 2" |
7,500 lbs. |
2,500 lbs. |
| LSG 1" - 2" |
10,000 lbs. |
3,500 lbs. |
| LSG 1 1/2" - 2 1/2" |
12,000 lbs. |
4,000 lbs. | |
| |
Lewis Snake Grips LSG-X |
|
 The LSG-X series performs the same function as the standard LSG series. The LSG-X cannot be taken apart in the middle, it is permanently attached via our new “Swivel Tube” Assembly. This swivel tube assembly is a low profile heavy-duty friction swivel. This snake is for the customer who does not need to separate the two pulling grip elements and who prefers a very low profile swivel. The swivel is permanently greased and has the size range and working load clearly stenciled on the swivel tube assembly.
|
| |
| Regular Size LSG-X Snakes |
| Part No. / Size Range |
Approx.
Brk. Stgth. |
Work Load |
| LSG-X 1/4" - 1/2" |
4,400 lbs. |
1,200 lbs. |
| LSG-X 1/2" - 1" |
7,500 lbs. |
2,500 lbs. |
| LSG-X 1" - 1 1/2" |
10,000 lbs. |
3,500 lbs. |
| LSG-X 1 1/2" - 2" |
12,000 lbs. |
4,000 lbs. |
| LSG-X 2" - 2 3/4" |
16,000 lbs. |
5,000 lbs. |
| LSG-X 2 3/4" - 3 1/2" |
20,000 lbs. |
6,500 lbs. |
| LSG-X 3 1/2" - 4 1/4" |
24,000 lbs. |
8,000 lbs. |
|
| Special Size LSG-X Snakes |
| Part No. / Size Range |
Approx.
Brk. Stgth. |
Work Load |
| LSG-X 1/4" - 1 1/2" |
4,400 lbs. |
1,200 lbs. |
| LSG-X 1/2" - 1 1/2" |
7,500 lbs. |
2,500 lbs. |
| LSG-X 1/2" - 2" |
7,500 lbs. |
2,500 lbs. |
| LSG-X 1" - 2" |
10,000 lbs. |
3,500 lbs. |
| LSG-X 1 1/2" - 2 1/2" |
12,000 lbs. |
4,000 lbs. |
|
READ THIS BEFORE
USING YOUR LSG SNAKE |
GUIDELINES FOR PROPER INSTALLATION AND USE OF LEWIS TYPE "LSG SNAKE" ROPE & CABLE CONNECTOR GRIP
-
Safety is always No. 1. Make sure no one is under the line as it is being pulled through the blocks and crown.
-
Be sure that the right size range grips being used for the line or rope being pulled. For example, for 13/8” drilling line, use the LSG 1 - 11/2” snake. When pulling a larger line with a smaller line (replacing the smaller with the larger), make sure the smaller line has the correct size grip and that the new larger diameter line has the correct size grip as well. LSG snakes are available with any required size range on either side.
-
Make sure the cable is clean and free of grease and oil in the area that will be loaded into the LSG snake. A high grade degreaser and heavy duty disposable towels are recommended for this purpose.
-
When loading the cable into the grip, be certain the cable is inserted all the way into the grip until the grip is fully loaded (into the plastic boot area below the pulling eye of the grip). Also examine both grips for cable abrasion or broken cables. An LSG snake showing any signs of cable fraying, broken cables or distorted hardware should be immediately discarded and replaced. Inspect the LSG Snake Grip prior to each use.
-
Once the snake is loaded properly, clamp the tail end of the grip using a Band-It® brand banding device. It is also recommended to tape over the bands to create a smoother, snag-resistant surface.
-
If you have any questions or comments regarding the safe usage of your LSG Snake, please call Toll Free at:
1 (888) 398-4719 |
|
BAND-IT® tools
BAND-IT banding tools are used to tie down ends of LSG Snake Grips, Pulling Grips and Splicing Grips for added security.
Bands are made of #201 Stainless
Steel and come in a few sizes.
The most popular sizes are:
L-203 (1/4" W x 10" L)
L-208 (1/4" W x 26" L)
Pok-It II Model J-020 Medium to Heavy-Duty
Thriftool Model J-075 Light Duty
Use the tools to tie down ends of pulling grips and splicing grips for added security. Use a BAND-IT® tool and bands instead of tape. Taping is not reliable and can be a safety hazard especially in overhead high tension pulling applications. Also in many cases splicing grips are permanently installed and in these instances taping just won’t last and can be dangerous.
Invest in a BAND-IT® tool and rest assured your cable will stay in place. The Thriftool requires a 1/2" socket or wrench, small hammer and cutting pliers while the Pok-it II requires only a small hammer. Both are easy to operate. |
|
|
|
Wire Rope Snake Grips
